A car isn’t cheap. According to , Americans spend approximately $36,000 on new cars. That means if you $10,000 in a year’s savings, it will take you about four years to own a brand new light vehicle.
Throw in the average that goes into car maintenance and repairs annually, and you’ll see why you should keep your car in the best working condition possible. But, of course, that means going for regular check-ups and repair services.
The clutch system, which includes the flywheel, is one component that requires regular maintenance.
What is a Flywheel, exactly?
A flywheel is a large metal disc with teeth on the edges that forms an integral part of the clutch system in a manual transmission car. Basically, from the engine and supplies it when required.
The following are some of the most important functions of a flywheel:
- It assists in starting the engine by providing initial inertia and a ring gear through which the starter motor is engaged to start the engine.
- Link the engine to the transmission: The flywheel connects the engine to the transmission, allowing the clutch to send power to the wheels.
- The flywheel provides the rotational inertia that keeps the engine operating smoothly. When you take your foot off the gas, this prevents speed fluctuations. The engine would stall if it didn’t have it.
- The flywheel is bolted between the clutch and the engine, assisting in the balance of the crankshaft.
As you drive a manual transmission automobile, the clutch constantly gets into contact with the flywheel anytime you release the clutch pedal. With time, the flywheel suffers wear and tear due to the heat and friction produced by normal clutch operations.
As a result, the flywheel’s surface wears down and smooths out as it absorbs and dispels heat. As a result, it reaches the point when the clutch slips.
More heat is produced than the flywheel can absorb at this stage. Because to the unequal application of heat, the flywheel surfaces begin to distort and develop heat cracks and hot spots as a result of increased heat stress.
As a result, it begins to vibrate when the vehicle is engaged or accelerates. It’s suggested that you get your flywheel resurfaced or replaced at this stage.
What is flywheel resurfacing, exactly?
Flywheel resurfacing is a typical repair procedure that involves removing a thin layer of metal from the disc’s surface to create a new, rougher surface that improves grip.
The depth of the heat cracks and blisters determines how much metal is removed. The flywheel can only be resurfaced if it does not fall below the manufacturer’s criteria for proper functioning, weight, and safety. If the flywheel is too thin and worn to be resurfaced, you’ll have to replace it completely.
When your clutch begins to slip or when you replace the clutch, the pressure plate, disk, or throwout bearing, it is recommended that you have your flywheel resurfaced.
The only question you have is: where can I get a flywheel refinished in my area?
Short Answer: Understanding where to get your flywheel resurfaced will help you keep your car safe to drive, avoid accidents, and damage to other parts, all of which can drive up your maintenance expenditures.
Furthermore, installing a new flywheel is nearly ten times more expensive than resurfacing an existing one. As a result, getting your flywheel resurfaced until it reaches the end of its useful life can save you a lot of money.
Auto parts stores and service centers such as NAPA Auto Parts, AAMCO, and OReilly Auto Parts are among the best places to get a flywheel resurfaced.
Flywheel resurfacing is available at some NAPA Auto Parts and OReilly Auto Parts shops. As a result, before visiting, call your local NAPA or OReilly to see if they offer flywheel resurfacing.
Flywheel resurfacing services are also available from local machine shops and mechanics. Certain machine shops, on the other hand, may lack mechanical expertise for specific vehicles.
So look for reliable automotive machine shops that can provide high-quality service. If you can’t find a reputable local mechanic who can resurface your flywheel because there aren’t any auto shops or machine shops in your neighborhood, try visiting a reputable local mechanic who can resurface your flywheel.
You can easily find machine shops and mechanics that resurface flywheels in your area with a quick Google search, then call or check the shop’s advertised services and prices. Alternatively, use the to locate certified mechanics near you.
Is Resurfacing a Flywheel Necessary?
- Is Resurfacing a Flywheel Necessary?
- How Long Does a Flywheel Last?
- How to Tell if a Flywheel Needs Resurfacing?
- How Much Does Flywheel Resurfacing Cost?
- How Long Does It Take to Resurface a Flywheel?
- Places To Get Flywheel Resurfacing Near Me
- Places That Don’t Resurface Flywheels
- Can You Resurface a Flywheel Do-It-Yourself at Home?
- How to Clean a Flywheel Yourself?
- Places to Get Flywheel Resurfacing Summary
Indeed, resurfacing a flywheel is necessary if the surface has been damaged by heat cracks and blisters and there is enough mass to cut.
When your clutch slips and vibrates while engaged or under acceleration, you should have your flywheel replaced right away. Experts advise refinishing your flywheel whenever you replace your clutch.
Failing to resurface a worn-out flywheel might cause the freshly fitted clutch to wear out prematurely, voiding the manufacturer’s warranty. Sadly, most clutch dealers will not respect the warranty if the flywheel was not resurfaced or was resurfaced incorrectly before installing the clutch.
Likewise, resurfacing a flywheel is less expensive than replacing the entire component. Thus, if there’s enough metal left to shave off, there’s no reason you shouldn’t resurface your flywheel to save money on car maintenance.
Always ensure that your flywheel is resurfaced correctly the first time to reap the cost-saving benefits. Making a mistake now can end up costing you a lot of money in the long run in terms of repairs and labor. As a result, make certain that the resurfacing is done correctly by a qualified mechanic.
A flywheel does not need to be resurfaced if the surface is flat and free of flaws. Resurfacing the flywheel, however, may bring it below the manufacturer’s standards for good operation if it is sufficiently worn. You’ll have no choice but to replace it rather than resurface it in that instance.
So whether or not to resurface a flywheel is necessary does come down to its condition. The easiest way to determine if your flywheel needs to be resurfaced is to unscrew it from the engine and have it thoroughly inspected by an expert. It’s also important to When purchasing a used vehicle, inspect it thoroughly..
A trustworthy technician will look for discolorations, warping, hot spots, heat cracks, and uneven wear on the surface. They’ll then evaluate the flatness of the surface with mechanical equipment like a straightedge and a feeler gauge. It assesses if there is sufficient metal for resurfacing.
How Long Does a Flywheel Last?
Resurfacing your flywheel is an excellent method to keep it in good shape, extend its life, and guarantee that power is transferred smoothly from the engine to the transmission.
But, that will only go it so far before it reaches the end of its useful life. You wish to avoid a flywheel failure, in which the vehicle suddenly stops in the middle of the road. Knowing how long a flywheel lasts is useful.
Fortunately, a flywheel is one of your car’s most durable components, lasting anywhere from 80,000 to 100,000 miles. But, the length of time your flywheel disk lasts may be affected by your driving skills, experience, and the environment in which you operate.
If you use your clutch for a long time before replacing it, it may slip and lose traction against the flywheel, resulting in a power transmission disconnect. It has the potential to shorten the lifespan of the flywheel by causing it to wear out faster.
Yet, if you drive your flywheel to the last mile, your automobile may lose power totally and come to an unexpected stop. If your clutch problems remain after resurfacing your flywheel, it’s a good idea to replace it.
Noise, vibration, or chattering when the flywheel is engaged while the automobile is accelerating are common symptoms that it needs to be replaced. While replacing the clutch, make sure the flywheel is checked for warping and damage to avoid it failing.
How to Tell if a Flywheel Needs Resurfacing?
The flywheel, like any other component, displays indicators of wear or damage when it is excessively worn or damaged. The following are signs and symptoms that your flywheel needs to be resurfaced or replaced:
When you shift into neutral or another gear, your car slides out of gear. This is due to the clutch’s inability to keep the flywheel from slipping.
Engine Accelerates With No Ground Speed
If the clutch fails to engage properly with the flywheel, the engine speed rises without a corresponding increase in ground speed. As a result, it will impair your driving skills and may possibly cause clutch damage.
Inability to Change Gears
It’s a symptom that your flywheel needs to be replaced. You won’t be able to drive at all because you can’t change gears. There could also be problems with other transmission components.
When the flywheel becomes worn, it is unable to absorb all of the heat generated by friction in the clutch. A burning odor pervades the passenger cabin as a result of the excessive heat. When depressing or releasing the clutch, it may make a rattling noise.
Vibrations or trembling in the clutch pedal, or worse, on the vehicle’s floor, are caused by a faulty flywheel. When you engage the clutch, the surface will feel distorted and the clutch will grab.
Damaged teeth on the flywheel’s edge can cause inability to start or inconsistent starts. As a result, it will be unable to engage the starter motor. When the starter motor is turned on, you’ll hear an unusual noise.
It’s a sign that your flywheel is too light to hold enough rotational inertia if the engine stalls or the speed drops whenever you let go of the gas pedal.
Even when the clutch is engaged, an uneven flywheel can generate vibration throughout the powertrain.
Take your flywheel to a professional auto technician if you see any of these indicators. Blisters, heat cracks, warping, an uneven surface, and decolorizations will all be looked for. It assists you in deciding whether to resurface or replace a flywheel.
How Much Does Flywheel Resurfacing Cost?
The cost of flywheel resurfacing varies depending on where you live and what kind of car you have, but in most cases, the cost does not surpass $50. As compared to the expense of purchasing and installing a new flywheel, this is a bargain.
New flywheels, for example, can cost anywhere from $50 to $400. Some, such as dual mass flywheels, may even be more expensive. You must also consider labor costs, which may be in the same ballpark depending on the mechanic’s hourly rate.
This means that purchasing and replacing a new flywheel might cost more than $1,000. On the other hand, for $50, it makes flywheel resurfacing affordable!
As a result, resurfacing your flywheel on a regular basis aids in the smooth operation of your clutching system. It also helps to avoid expensive replacements if the flywheel is damaged beyond repair.
How Long Does It Take to Resurface a Flywheel?
A flywheel can be resurfaced in a short amount of time. It just takes 3-4 minutes to resurface a flywheel after it has been screwed out of the engine.
However, depending on the method used, the time it takes to resurface a wheel may vary slightly. Grinding is the quickest and most popular way to resurface a surface. The fastest method is to use a dedicated grinder.
Nevertheless, a forward and block grinding machine can be used, albeit this will take longer. This approach has the advantage of not missing hard places, resulting in a smooth, uniform surface.
The third way involves shaving a small metal layer from the flywheel’s surface with a brake lathe. Unfortunately, setting the flywheel on the lathe takes time, making this process slow. Furthermore, missed hot spots may result in an uneven surface.
Installing a new flywheel, on the other hand, is a different story. A mechanic may need up to 5 hours to replace a flywheel. That’s because they have to remove the engine and double-check that everything is in its proper location before reinstalling it.
That is why replacing a flywheel rather than resurfacing is more expensive.
Places To Get Flywheel Resurfacing Near Me
You now understand what a flywheel is, how it functions, and the differences between resurfacing and purchasing a new flywheel with installation. You can visit a neighboring mechanic with confidence, knowing that you will not be exploited.
Nonetheless, you’ll need to hire expert mechanics to ensure that the operation goes smoothly. Mistakes may be costly, as you are well aware.
So, where do you look for reputable flywheel resurfacing professionals to conduct the job? We’ve done our homework and prepared a list of the best local flywheel resurfacing companies, including:
1. O’Reilly Auto Parts
One of the best places to get your flywheel refinished is OReilly Auto Parts. Because the auto shop employs professional technicians to address a variety of mechanical issues for their consumers, this is the case.
In addition, OReilly has about 5600 local stores in 47 states, as well as about 22 in Mexico.
OReilly mechanics, on the other hand, will only resurface your flywheel if there is enough mass left to cut without bringing it below the manufacturer’s specifications. The flywheel must be replaced if this is not the case.
The good thing is, they also sell all sorts of automated tools, equipment, supplies, and accessories, like cabin filters and engine air filters and Drive-in theaters have FM radios.. So if your flywheel is worn out and cannot be resurfaced, they’ll sell and install a new flywheel for you.
Save some money by finding the the best place to buy discounted gift cards.
Find a to get your flywheel resurfaced or get rotors turned.
A neighboring NAPA Auto Parts store is another excellent option for flywheel resurfacing. The National Automotive Parts Association has approximately 6,000 stores and over 15,000 NAPA AutoCare repair facilities that provide maintenance and repair services.
NAPA has experienced mechanics at its AutoCare facility because it is a reputable auto parts retailer.
Even if your flywheel needs replacement, you can purchase it at a nearby NAPA store and install it at one of their facilities. The auto parts stores carry all sorts of automotive replacement parts and accessories, like the the best winch batteries, RV batteries with a long cycle life, and carpet extractors for auto detailing to maintain your automobile clean.
See our guide for the the top online coupon sites for saving money on purchases.
Find a nearby to get your flywheel resurfaced.
AAMCO is a well-known auto transmission repair franchise that has been around since 1957. As a result, you’ll have access to transmission repair specialists that can repair your clutch system and resurface your flywheel to keep it in good working order.
About 260 locations across the country offer brake repairs, flywheel resurfacing, A/C services, tune-ups, and motorcycle oil changes.
You can expect to pay more to have your flywheel resurfaced at an AAMCO location due to their specialized auto services. But that’s what you get for hiring an expert!
But, there are just a few locations, so you might not be able to find an AAMCO Total Vehicle Care near you. But it’s never a bad idea to give it a shot.
Find a to get your flywheel resurfaced.
4. Local Mechanics
If you can’t find any auto parts stores or service shops, a local mechanic can resurface your flywheel.
Independent technicians are usually trained car repair experts, so if you find a reliable mechanic, you can expect high-quality service. And the good news is that you can always try to bargain down the price to get a good deal.
The most straightforward way to locate respectable mechanics in your neighborhood is to conduct a Google search. Enter the term “local mechanics near me” in the search box. You’ll get a list of surrounding local repair businesses, as well as information on the services they provide, contact information, and directions.
When visiting a local location, phone ahead to learn about their flywheel resurfacing services and rates.
Alternatively, use the to locate certified independent mechanics nearby.
5. Local Machine Shop
Flywheel resurfacing services are also available at local machine shops. Companies may have automotive professionals on staff to assist consumers with various auto repair services.
Unfortunately, some machine shops may lack the necessary competence to work on specific types of vehicles, so look for reputed machine shops that provide high-quality services.
Do a simple Google search for Machine shops near me or local machine shops that offer flywheel resurfacing to uncover local machine shops that supply flywheels.
Google will provide you with a list of local machine shops as well as the services they provide. Examine the shop’s advertised services and customer reviews to verify if they can complete the task. Of course, calling ahead to confirm services and charges is usually a smart idea.
You may occasionally find someone at the shops that do extra money through under-the-table jobs.
Places That Don’t Resurface Flywheels
New flywheels are sold at several car parts stores and repair shops, but old ones are not resurfaced. Understanding where to go that just sells versus where to go that only repairs might save you time and money.
The following are some of the top places that do not provide flywheel resurfacing:
Can You Resurface a Flywheel Do-It-Yourself at Home?
Yes, you can do your own flywheel resurfacing at home if you have the necessary mechanical abilities and materials.
A flywheel, on the other hand, is an essential component of your vehicle. So only resurface it at home if you are confident in your abilities. If the flywheel is damaged, you’ll have to pay a mechanic to replace it, which could cost over $1,000.
It’s best to only remove the flywheel to inspect it for damage. Then take it to a trustworthy technician to get it thoroughly resurfaced.
Mechanics are equipped with the necessary automotive tools, such as a straightedge and a feeler gauge. A mechanic can also tell you whether your flywheel can be resurfaced or if it has to be replaced.
This video demonstrates how to remove, examine, and resurface your flywheel by hand or by machine at home.
How to Clean a Flywheel Yourself?
Here’s how to clean a flywheel yourself, step by step.
- Hands-on: Use a mild soap to clean your hands before handling the flywheel. The surface of the flywheel might be damaged by grease and oil on your hands.
- Apply a homogeneous coat of brake cleaner to the flywheel’s surface.
- Clean the Flywheels Surface: Scrub the flywheels surface with a rough dish cleaning pad while moving your hand in small circular motions to avoid gouging the surface.
- Pour a big amount of brake cleaner on the flywheels to rinse them off and remove any leftover particles.
- Give time for the flywheel to dry: Wait 2-3 minutes for the flywheel to dry. Then use compressed air to eliminate any leftover particles and dry any remaining cleaner.
You’ve completed the task! That’s how simple it is to clean a flywheel.
Places to Get Flywheel Resurfacing Summary
The flywheel is an essential part of your car that helps store and transmit power to different parts. If left in a damaged condition, the engine can stall and result in costly repairs and replacements. In addition, a bad flywheel can prevent you from changing gears and makes your vehicle unreliable if you’re using it as a pilot car driver, receive compensation for delivering automobiles, or you It is possible to get paid to advertise on it.
By getting your flywheel resurfaced regularly, you can lengthen its lifespan and save money fast.
Some of the finest places to get your flywheel resurfaced are auto dealers and repair centers. If you can’t find one in your area, certified mechanics or machine shops can provide flywheel resurfacing services.
Resurfacing a flywheel costs approximately $50 and takes less than 5 minutes, compared to a new flywheel costing over $1,000 and requiring 3-4 hours of labor. As a result, it’s a good idea to have your flywheel resurfaced whenever you change your clutch.
See our guide on how to become an enormous vehicle pilot auto driver.